Відео

When you attach the knee blocks to the front and side of the legs is there anything you have to address, like the two blocks touching? Do you just leave a space between them or are they mitered? I wasn't able to see what the underside of yours look like.

Why do you not glue the top of the kneeblock?

The golf glove tells all. Pure mastery.

Where does one purchase a piece of mahogany the width to accommodate the Walker table? What type of mahogany is it?

I just wanted to say how much I enjoyed your videos on this stepping stool. Inspirational to me to the point that I made my own! Thank you

good morning sir. I have searched the internets high and low and you are the only other human who apparently has had this issue to fix. thank you for documenting your process! I inherited a 120 year old dresser and had to replace (non-original hardware). When bending the bails for the convex handles, do you ever heat or anneal them in anyway post bend?

For the algorithm.

Was pleasantly surprised to see you back to work.Thanks for sharing your work with us.

Glad you are back!

Good to see you again. Thanks for posting the videos.

Thank you for taking the time to produce,edit and mostly teach with your videos, David. A tilt top table such as this is next up for me, so I am watching with great interest and appreciation! Also, LOVE the silent shoutout to SAPFM! Be well - Diane

Do they even have mahogany trees that large anymore, or was it glued together?

It’s good to see one of the finest craftsman around back on the scene. Keep it going.

Good to see you back Dave! Hope your doing well. Excellent work as always.

Can't wait to watch. Glad your back at it .

Yes, glad to see you back. I have always been impressed with your work.

Welcome back! Glad to see you are doing well. thanks for the videos.

I haven't seen you in a while. It's great to see you yet again

Glad to see you back

One board at 30" wide, that's gotta be hard to come by. Nice to see you back.

Glad your back

Good to see you back! Love how in depth you go on the technical aspects.

David your voice was cut off at the end, no harm no foul, after-all your fine woodworker not David lean This is going to be very interesting

So glad to see you again. I always enjoy your videos and have missed seeing your work.

Out of curiosity, how does the level of hardness to carve this compare to ball and claw foot? I ask because I’m currently taking an evening carving class and am doing a ball and claw. Will re do that at least once and then thinking to go to the fan next. Would like your thoughts. Thanks.

Sure have learned alot watching your videos. Getting close to starting one of those. Why couldn't you make a radius template to use to periodically check while carving the ball portion? Thanks for taking the time to film and offer your craft to us.

Do you offer the plans or templates for this chest?

David, wonderful work as always. Truly inspirational. Curious if you are a member of SAPFM ?

Wow, that’s some kinda air hose man .

Ended up here as I’m learning about different finishes as I get into stripping paint & refinishing the old cherry veneer doors in our house. But I admit I didn’t hear anything you said while “Appalachian Spring” was playing. ❤❤❤

“We’re going to be careful when we do that “. Thanks, I’m a better woodworker now .

Dang , that’s nice work !

Hey folks, you have found the best master woodworking source on the web .

STUPID ...!!!!!

Hi David! Your content is amazing for aspiring woodworkers. I have a question, I recently bought some mahogany logs that I milled in different measurements, one of them being 4/4 + 1/8. To my dismay, the sawmill guys left some a bit thinner that that, around 1 1/16 and 1. These are wide boards at about 25 inches, they are dead flat though. Do you think it is feasible to hand plane them to 7/8s? Many reproductions use that size as a standard and I'm concerned if I will be able to get them there. Note; The lumber is dry and very flat. Thanks in advance for your valuable help!

Ok thanks you.

David are still posting your videos on UA-cam? I very much enjoy your work and skill

That string you used for sizing the ball appeared to be weed whacker trimmer line. It was fairly stiff which worked well. If it wasn’t, I think I will try my weed whacker trim line for such measurements.

David what is your opinion of clamping pressure when gluing up a panel say? I’ve come across different opinions and with your skill level I’m curious as to what your approach is? Thanks

I may have missed this but my question is why Waterlox? I’ve never used it before and I’m curious why it appeals to you. I tend to use a lot of General Finishes products.

Beautiful!! Are your plans available? I would love to make that Beautiful piece. You've done a wonderful job.

Sure wished you lived near me. I would love to learn from you. Great Job. And Great explanation of a complicated process.

The scrapers you make from putty knives do you turn a bur on them or leave them flat?

Next time try making a square wood or plastic base for you Router, that fits in your jig. You had to much play using you Router.

Was the stock you cut the leg from 4"x4" or ?

Enjoy watching your videos. I see you haven't posted in a while. I hope all is well by you

Do you make your working drawings by hand or a computer? Thanks

The drawer sides for narrow document drawers are they are pine ?

Beautiful 👏👏👏👏

Do you use a burnisher to put a hook on the putty knife scraper?